COLOURS
STANDARD EXTERIOR LINING COLORS
RAL 3000
RAL 8017
RAL 5010
RAL 6011
RAL 9002
RAL 9006
RAL 7016
RAL 9007
RAL 7035
RAL 9010
STANDARD INTERIOR LINING COLORS
RAL 9002
RAL 9010
USAGE
OUTER WALL - HORIZONTAL ARRANGEMENT OF PLATES
insPIRe® S sandwich panel
Construction screw
Polyethylene sealing tape (PES)
Flashings the foundations
Plate flashing
Corner flashing
Construction of the object
The use insPIRe® S sandwich panels with visible fastening is a solution optimized for economic and strength reasons. The availability of panels in two modular widths minimizes the waste generated during assembly.
OUTER WALL - VERTICAL ARRANGEMENT OF PLATES
The use of insPIRe® U sandwich panels with invisible fastening improves the visual effect of the building's facade. In addition, the use of flashings offered by Gór Stal and dedicated mounting accessories facilitates panel assembly and finishing works.
insPIRe® U sandwich panel
Construction screw + washer PM-1
Polyethylene sealing tape (PES)
Flashings the foundations
Corner flashing
Construction for sandwich panels
Construction of the object
PARTITION WALL - VIEW FROM THE SIDE OF THE PLATES
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
insPIRe® S sandwich panel
Construction screw
Polyethylene sealing tape (PES)
Flashings for joining panels to the floor
Plate flashing
Construction for the inner wall
CEILING - BOTTOM VIEW
insPIRe® S sandwich panel
Construction screw
Polyethylene sealing tape (PES)
Plate flashing
Flashing the connection of panels with the wall
Ceiling construction
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
CEILING - TOP VIEW OF THE STRUCTURE
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
insPIRe® S sandwich panel
Construction screw
Polyethylene sealing tape (PES)
Plate flashing
Flashing the connection of panels with the wall
The ceiling structure is adapted to the mounting conditions of the panels
INSTALLATION OF PANELS
Sandwich panels are a commonly used building material for light external envelope cladding of industrial halls, warehouses and production buildings, department stores and commercial facilities, office buildings, administrative buildings and cold storage facilities. Installation of sandwich panel can be performed in almost any weather conditions.
COMPLEMENTARY PRODUCTS
GASKETS AND OTHER ACCESSORIES
Gaskets for sandwich panels
Sealing flanges intended for passage of ducts (e.g. ventilation) through the casing made of sandwich panels
Bushings - washers for cold plates
We supply adhesive, polyurethane (PUS and PURS), polyethylene (PED) and butyl sealing tapes
SELF DRILLING SCREWS:
for hot rolled construction (wall thickness from 3 to 12 mm)
for cold-bent construction (thickness from 1.5 mm to 5 mm)
On special order it is possible to provide caps or connectors in the color of the outer cladding of the sandwich panel. Panels can be joined to steel, reinforced concrete and wooden constructions using dedicated fasteners. Detailed information on connectors can be found in our technical catalogues.
FLASHINGS
Length: 3000 mm or 6000 mm
Material: galvanized steel sheet
Protective coating: polyester varnish
Additional protection: foil
Manufacturer has a profiling machine that allows bending of 1.25 mm thick sheet metal (maximum length of 6 m), in typical shapes from the catalog and according to the individual design of the customer. Detailed information on sheet thickness and colors can be found in the catalog dedicated to a specific panel.
The flashings are protected against damage by foiling the top side. Detailed data is available in the section "For designers - flashing"
Steel flashing are part of the insulation panel system - Sandwich Panels.
Additionally, they are used as a separate decorative element.
Steel flashing is made of galvanized metal sheet with a thickness of 0.5 mm, 0.7 mm and 1.0 mm, colors according to the RAL palette.
Standard length of metal flashing sheet is 6.0 m.
Contact us for detailed information regarding specific panel thickness, span and type of application.
Want more information on sandwich panel house? Click the link below to contact us.
If you have any questions on plastic litter bin manufacturer. We will give the professional answers to your questions.