3/4 inch SS201 welded wire mesh is a welded stainless steel grid with a nominal opening of 3/4 inch, equal to 19.05 mm. It is made by welding intersecting wires together, with the opening size, wire diameter, sheet or roll dimensions, and finish specified for the order. It can suit general-purpose screening, protective enclosures, and fabrication where a stainless steel mesh is appropriate, but SS201 should not be treated as interchangeable with more corrosion-resistant grades in every environment. Before ordering, confirm the opening measurement method, wire diameter, material grade, and intended service conditions with your supplier.
You can find more information on our web, so please take a look.
This guide is for importers, fabricators, distributors, and project buyers comparing 3/4 inch SS201 welded wire mesh for a defined use. It is especially useful when a drawing or supplier quotation lists only the opening size, leaving other important details unclear. We recommend treating the mesh specification as a combination of material, opening, wire diameter, dimensions, and finish—not as a product name alone. A complete specification makes supplier comparisons more meaningful and helps reduce avoidable changes after ordering.
The 3/4 inch designation converts to 19.05 mm, but buyers should confirm whether that figure refers to the clear opening or the distance between wire centers. These measurements are not the same: wire diameter changes the distance from one wire center to the next. For example, if a project calls for a 19.05 mm clear opening and uses an illustrative 1.0 mm wire, the center-to-center pitch would be 20.05 mm. This example explains the measurement relationship; it is not a guaranteed standard configuration or a statement of available stock.
Wire diameter should be selected according to the mesh’s job, not simply copied from another project. A heavier wire generally adds material and can make the grid more rigid, while a lighter wire may be suitable where lower weight or finer fabrication is important. The correct balance depends on span, handling, loading, installation method, and the required level of protection. Ask the supplier to state the wire diameter in millimeters and identify how it is measured.
SS201 is an austenitic stainless steel grade used in a range of fabricated products, but its corrosion behavior depends on the surrounding conditions and the exact material supplied. As a general selection principle, do not assume SS201 will perform like SS304 in environments involving persistent moisture, salt, chlorides, or aggressive chemicals. If corrosion resistance is critical, describe the exposure conditions and compare suitable grades before placing an order. A supplier can help clarify material options, but the final grade should match the project’s technical requirements.
Welded mesh consists of crossing wires joined at their intersections, creating a fixed grid rather than a woven structure. Buyers should review the weld appearance, grid consistency, edge condition, and finish against their application and acceptance criteria. If the mesh will be cut, bent, coated, or fitted into a frame, discuss those processes before confirming the order. State whether the project requires a particular surface finish or simply an agreed, clean commercial finish.
Potential uses for 3/4 inch SS201 welded wire mesh include general screening, guards, partitions, equipment enclosures, and fabricated panels where the opening and wire strength meet the design need. The 19.05 mm nominal opening may allow airflow and visibility while providing a physical grid, but the actual suitability depends on the object being retained or excluded. It should not be specified as a safety barrier, load-bearing component, or animal-containment solution without checking the relevant design and performance requirements. For food-contact, chemical-processing, or regulated uses, confirm material and compliance requirements with the responsible technical team.
Shunqiang Wire Mesh Product Page
Environmental conditions can change the material decision even when the opening and dimensions are correct. Indoor, relatively dry applications may have different demands from outdoor locations or washdown areas exposed to salts or cleaning agents. Consider whether the mesh will be in direct contact with dissimilar metals, because the installation details can affect corrosion behavior. When the environment is uncertain, share photographs, process details, and cleaning conditions with the supplier and your engineering team.
Ask for a drawing or written specification when the mesh will be integrated into a larger assembly. A quotation should identify the material grade, opening definition, wire diameter, dimensions, form, finish, quantity, and packaging basis. If any detail is unavailable, mark it as a point to confirm rather than assuming that two suppliers use the same convention. For repeat orders, retain the approved specification and, where practical, an agreed reference sample.
The price of 3/4 inch SS201 welded wire mesh can vary with wire diameter, product dimensions, order quantity, finish, fabrication, packaging, and shipping destination. Material usage generally increases with heavier wire and larger product dimensions, while custom cutting or packing can add processing requirements. A low unit price is not a complete comparison if the quoted mesh differs in grade, opening definition, or wire diameter. Request quotations on the same written specification to compare them fairly.
Minimum order quantity and lead time depend on the supplier’s production schedule, available material, requested configuration, and order details. We recommend asking whether the quotation is based on standard production or a made-to-order specification, and whether samples or pre-shipment checks are available for the project. Confirm the quotation validity, payment terms, packaging, shipping method, and delivery basis directly with the supplier. These details are commercial terms and should not be inferred from the mesh designation.
Reliable sourcing depends on clear communication as much as on the nominal mesh size. Check that the supplier’s written offer matches your purchase specification and that any deviations are disclosed before approval. For ongoing supply, discuss how repeat orders will be identified and whether the supplier can retain the agreed product details. Avoid relying on broad statements such as “stainless” or “standard mesh” when the project requires a particular grade and geometry.
At Shunqiang Wire Mesh, we support B2B buyers by reviewing the requested opening, wire diameter, material, dimensions, and product form before quotation. Share your drawing or specification, application environment, required quantity, and destination so we can assess the requested configuration and identify details that need confirmation. We can discuss the available production options and coordinate quotation information for your purchasing review. Availability, MOQ, and lead time are confirmed against the specific order requirements.
3/4 inch SS201 welded wire mesh is a suitable candidate when a nominal 19.05 mm grid opening and SS201 material meet the application’s mechanical and environmental requirements. The opening label alone is not enough to finalize a purchase: confirm clear opening versus pitch, wire diameter, grade, finish, dimensions, and tolerances in writing. Then compare supplier quotations using the same specification and check MOQ, lead time, inspection, and packing terms. Send Shunqiang Wire Mesh your project details or drawing to discuss a configuration and request a B2B quotation.
Want more information on 3/4 inch ss201 welded wire mesh? Feel free to contact us.